Home > Dvd Drive > Replacing DVD Drives - IDE To SATA

Replacing DVD Drives - IDE To SATA


Take care not to loosen anything else within the case while removing the cables. Skip to main contenteBayShop by categoryEnter your search keywordAll CategoriesAdvancedHi (Sign in to bid or buy) Daily Deals Gift Cards Sell Help & Contact My eBayExpand My eBay Summary Bids/Offers Watch Back and Front of Syba's Drive Connector Special Power Plug & SATA Data Cable   (Syba and Amazon) Since the black connector attaches directly to the end of your disk drive, you Continue to the next Step. useful reference

If you are not replacing a drive then you will need to remove the blank from the computer case at the front of the drive bay where you want the drive. The marketing blurb says "burn the disk, flip it, then burn the label". Inspect the BIOS configuration panels to see if you can change settings to get the behavior you want. IDE for Optical Drives solved Replacing an optical drive with a 3.5" HDD solved SATA or USB for an optical drive?

How To Connect Ide Dvd Drive To Sata Motherboard

Currently it has a basic IDE CD ROM drive from the factory. SATA power connectors are almost always black; Molex connectors are almost always white. This is an easy way to add an IDE drive to a motherboard with a single IDE motherboard socket. Be careful not to slide skin along any interior metal edge of the computer.

They use SATA for their hard disk(s), and the single IDE socket to connect a legacy DVD/CD drive (using the IDE ATAPI optical drive standard). Next take the screws that came with your CD/DVD Writer and secure the device so it is flush with the front of your case (fig 1.5). Ultimate Handyman 105.167 görüntüleme 3:28 IDE to SATA or SATA IDE Adapter HDD DVD Converter - Süre: 1:28. Dvd Drive Power Cable This will enable a sufficient amount of air to flow between the two drives.

If you already have an optical drive installed then if possible leave a gap in-between it and the new drive. How To Connect Dvd Drive To Motherboard SATA's physical connectors for consumer computers have remained the same throughout this evolution. Once the cables are in place ensure you have not loosened anything during the installation and proceed to put the covers back onto the case. http://www.wikihow.com/Replace-an-IDE-Dvd-Drive-With-an-SATA-Dvd-Drive How much degradation you experience depends on the patterns of your disk use and which IDE standards are involved. (I exclude these complexities here.) For typical office work this configuration works

Right-click the drive you want to remove. Optical Drive Power Cable Reklam Otomatik oynat Otomatik oynatma etkinleştirildiğinde, önerilen bir video otomatik olarak oynatılır. If the drive is not labeled, see the drive documentation. Yükleniyor...

How To Connect Dvd Drive To Motherboard

/ Debug Show log entry Show visual element tree Copy Visitor ID Show logging window Toggle dark mode Log Entry [[data.logEntryString]] Visual Element Tree [[data.veTree]] [[getSimpleString(data.formattedTitle)]] [[data.count]] [[_text]] [[_charCounterStr]] [[label]] click Should you decide to purchase any compatibility hardware, be sure to read product descriptions and user reviews before buying. - - - - - - - - - - - - How To Connect Ide Dvd Drive To Sata Motherboard Here's how the IDE connector sockets on the motherboard look, along with the ribbon cable that goes from the motherboard socket into the back of any IDE drive: PATA Photos (Wikipedia How To Install Dvd Drive On Pc Read his other articles here (0) 15 Comment(s) Related Articles Quantum computing is real, and D-Wave just open-sourced itMaking an MSX fontThe FireBee: modern Atari clone Technology White Papers See

So, have a look inside your computer case. Cable Select should be selected only when the devices are to be attached as the cable depicts, ie, the first connector (working away from the motherboard) is the slave and the IDEAn IDE (Integrated Drive Electronics) drive has a broad ribbon-like cable for transferring data to and from the drive, and a smaller, chunky four-pin connector to provide power. Most IDE disk drives use an IDE data ribbon connector and a white power plug, while most SATA drives use the SATA data cable connector and a black power plug. How To Install Cd Drive In Laptop

Repeat for the other panel. Behaviors of boards with both PATA and SATA sockets depend on the motherboard firmware and BIOS. Drive enclosure for permanent use. http://ps3coderz.com/dvd-drive/why-windows-spins-up-dvd-drives-when-i-press-sleep-button.php Click the Device Manager tab.

If you are using the Windows operating system go to My Computer and you should see your new drive there. Ide To Sata Converter For Dvd Drive Help answer questions Learn more 143 Articles & News Forum Graphics & Displays CPU Components Motherboards Games Storage Overclocking Tutorials All categories Chart For IT Pros Get IT Center Brands MESSAGES LOG IN Log in Facebook Google Email No account yet?

The power supply has a 20-pin main connector. 2 answers Last reply Jul 13, 2012 More about replacing optical drive sata optical drive SR-71 BlackbirdJul 13, 2012, 7:07 AM http://www.newegg.com/Product/Product.aspx?Item=N82E16812232004 SR-71

Did this article help you? You'll also run into occasional compatibility problems if you don't do your homework. Any computer built since mid-2007 will be very likely to have SATA connectors. Sata Optical Drive Figure : Securing the side panel Step 6: Installing drivers for the new drive Connect all cables and turn on the computer.

All trademarks, icons, and logos shown or mentioned in this web site are the property of their respective owners. When they are all in place tighten them completely. Another alternative is to buy an adapter card that plugs into the motherboard and has the sockets you need. Create an account EXPLORE Community DashboardRandom ArticleAbout UsCategoriesRecent Changes HELP US Write an ArticleRequest a New ArticleAnswer a RequestMore Ideas...

The most foolproof way to see what type of drive your computer can take is to open it up and take a look at the drive or drives it's currently using.